HVAC & Plumbing Services in Willoughby, OH

Conducted site assessment for mini split installation to supplement existing baseboard heating system. Customer requires cooling capacity for rooms located on opposite sides of residence. Evaluated electrical panel capacity and available breaker spaces in basement to determine feasibility of supporting two mini split units. Documented current electrical infrastructure including main panel configuration and available circuit capacity. Based on room layout and distance between target areas, recommended dual mini split system installation with separate outdoor condensing units to efficiently serve opposite sides of home.

Completed routine AC tune-up on 3-year-old cooling system. Performed comprehensive system diagnostics using digital multimeter to verify electrical performance and measure operating parameters. System tested within normal operating specifications with capacitor reading 476.7 MFD and voltage reading 49.95V. All components functioning properly with no deficiencies noted at time of service.

Completed comprehensive spring maintenance tune-up on 9-year-old air conditioning system. Performed standard diagnostic testing using digital multimeter to verify electrical parameters and system performance, including voltage readings and temperature measurements across critical components. All readings were within manufacturer specifications, and system is operating efficiently for the cooling season.

Returned to property to investigate reported leak on upstairs boiler unit. Upon inspection, identified moisture and water damage on wooden platform beneath boiler system. Located source of leak at brass T-joint valve fitting with compression-style connection. Valve showed signs of wear and minor seepage at threaded connection points. Inspected surrounding piping infrastructure, including insulated supply lines and associated ductwork. Documented conditions with photographs showing valve assembly, connection points, and water-damaged areas for service records. Recommended valve replacement and platform repair to prevent further deterioration and ensure system integrity.

Completed AC club maintenance visit on air handler system. Performed diagnostic testing using digital multimeter, measuring microamp readings on the Emerson control board to verify proper circuit operation. Inspected control board displaying diagnostic code "dl" and checked all wire connections and harness terminations. All electrical connections secure, system control board functioning within normal parameters.

Completed routine cooling maintenance and club membership renewal inspection on residential HVAC system. Performed comprehensive evaluation of outdoor condenser unit, which showed excellent condition with clean protective grille and no visible signs of wear, corrosion, or damage. Inspected exterior electrical disconnect box and associated conduit connections, confirming proper weatherproof installation and secure mounting to building exterior.

Responded to complaint of toilet continuing to run after homeowner installed new flapper. Upon inspection, found significant mineral buildup and discolored water throughout tank interior, indicating water quality issues and aged components in 20-year-old home. Diagnosed that fill valve assembly was malfunctioning due to mineral deposits interfering with float mechanism operation, preventing proper shutoff. Replaced fill valve assembly and adjusted water level to manufacturer specifications. Cleaned mineral deposits from tank interior and flush valve seat to ensure proper flapper seal. Tested flush cycle multiple times to verify complete shutoff and proper refill operation. System now functioning correctly with no continuous running.

Responded to service call for leaking hot water tank in 17-year-old residential property. Conducted visual inspection of water heater unit and surrounding plumbing connections to identify source of leak. Documented existing conditions with photographs for warranty verification purposes, as unit age falls within potential manufacturer warranty coverage period. Assessed leak severity and provided homeowner with recommendations regarding warranty claim process and potential replacement options given the age of the equipment and home.

Responded to emergency call for ceiling leak originating from heating system piping. Upon arrival, found active water intrusion with extensive ceiling damage, including compromised drywall, significant water staining, and exposed structural members. Inspection revealed severely deteriorated wooden joists and beams with dark staining indicating prolonged moisture exposure and potential microbial growth. Located source of leak at corroded heating system pipe running through ceiling cavity. Implemented immediate damage control measures by installing protective plastic sheeting to contain water flow and prevent further interior damage. Documented extensive deterioration of ceiling structure and heating pipe condition through photographic evidence. Advised customer of emergency nature of repairs needed and provided contact information for follow-up restoration work.

Performed routine cooling maintenance member visit on Trane air conditioning unit (Model A4AC3030A1000AA, Serial 20392NP5BF). Conducted system diagnostics using digital multimeter, recording temperature reading of 497°F at measured component. Completed standard inspection of 3-ton AC unit manufactured September 2020, verified unit specifications including 208/230V single-phase operation at 16.0 amps with R-410A refrigerant charge of 25 oz.

Performed warranty service to reseat air conditioning unit that had settled due to soil subsidence following excavation work. Unit was releveled and repositioned on stable foundation to ensure proper operation and prevent future mechanical stress on refrigerant lines and electrical connections. Documentation photos captured condition of work area showing evidence of settling and completed repositioning of equipment.

Completed full HVAC system installation including an 80,000 BTU furnace and 3-ton 15 SEER air conditioning unit with weathered top cabinet. Sealed return air panning throughout the system to eliminate air leakage and improve efficiency. Installed Aprilaire whole-home humidifier for enhanced indoor air quality and comfort control. Repaired and sealed 6-inch ductwork take-off connection that was previously compromised. Replaced fuses in electrical disconnect as part of system commissioning and safety verification. Installed water heater concurrent with HVAC equipment replacement. All equipment tested, leveled, and verified operational per manufacturer specifications.

Installed 50-gallon A.O. Smith standard vent gas water heater with drip pan capped per customer request to eliminate above-ground tripping hazard. Unit installed with proper gas connections, verified burner ignition and flame pattern, and confirmed all safety labels and specifications are visible on exterior of tank.

Completed return visit for cracked clay pipe replacement with PVC piping. Installed new toilet in bathroom with mosaic tile walls and performed leak repair behind dryer unit. All plumbing fixtures tested and verified operational upon completion.

Completed HVAC estimate for air conditioning system replacement on property with 12-14 year old existing AC unit that has experienced operational issues. Customer elected to proceed with AC replacement at this time and defer furnace replacement for approximately one year, despite existing furnace also being 12-14 years old. Inspected current system configuration including furnace control board, ductwork, and equipment layout in basement mechanical room. Documented existing equipment conditions and provided replacement options for relocating outdoor condensing unit to preferred location. Photographed furnace circuit board showing control wiring, relays, and flame sensor components, as well as overall mechanical room setup with gas furnace, water heater, and duct distribution system.

Completed routine HVAC club maintenance visit on both furnace and air conditioning system. Inspected dual-run capacitor rated at 45/5 µF 440V, confirmed proper operation and no signs of bulging or deterioration, and verified electrical connections secure with proper wire terminations. Measured system amperage readings using calibrated multimeter, recording 23.53 amps with zero inrush current detected, indicating normal compressor operation within manufacturer specifications.

Responded to outdoor hose bib leak at rear of residence. Upon inspection, found water seepage from spigot body despite shutoff valve being fully closed. Replaced faulty hose bib with new frost-free unit, ensuring proper seal against vinyl siding and verified complete water shutoff functionality.

Completed heating maintenance club visit on air handler system. Performed electrical diagnostics using clamp meter, recording amperage draw of 0.28 amps on system components. Measured static pressure differential across system using dual port manometer, with readings of 186 and 180, indicating proper airflow through the unit. All measurements within manufacturer specifications, confirming system operating efficiently for the heating season.

Replaced two bathroom faucets and connected new flexible braided supply lines to existing shut-off valves. Verified proper drainage through P-trap assembly and tested for leaks at all connection points.

Responded to gas odor complaint reported in basement and upper levels of residence. Performed comprehensive gas pressure test on system using calibrated pressure gauge to verify system integrity and identify potential leak sources. Conducted diagnostic testing on heating equipment with combustion analysis, confirming proper burner operation and flame characteristics while investigating reported gas smell throughout the property.