Reliable Heating, Cooling & Plumbing Services in Kirtland

Completed cooling maintenance on HVAC system per customer request for technician continuity. Performed diagnostic testing using digital multimeter to verify electrical readings at control board, confirming proper voltage levels at 396V and system operation within manufacturer specifications. Inspected Emerson control board and all associated wiring connections, terminal blocks, and electronic components for signs of wear or deterioration—all found to be in good working condition with clean solder joints and secure connections.

Repaired loose kitchen faucet handle by tightening the mounting hardware and securing the handle assembly to the pull-down spray faucet. Tested operation to ensure proper function and verified no leaks at connection points.

Responded to service call for 5-year-old Black and Decker tankless water heater with no hot water production since installation. Upon arrival, conducted comprehensive diagnostic assessment of the unit and associated utility connections. Inspected the natural gas supply line and meter installation at the exterior of the residence, noting visible corrosion and rust on gas line fittings and valve connections that could potentially affect gas flow to the appliance. Examined the basement mechanical room installation, including the complex PVC piping configuration and water distribution system connected to the tankless unit. Performed gas line pressure testing and verified proper gas supply availability at the meter. Identified issues with gas delivery system requiring further evaluation to restore hot water functionality to the previously non-operational tankless water heater system.

Installed customer-supplied toilet in residential bathroom, including securing the fixture to the floor flange and connecting the braided stainless steel water supply line to the wall-mounted shut-off valve. Tested the installation to ensure proper operation and verified no leaks were present.

Responded to a running toilet complaint and identified a faulty vacuum breaker assembly. Removed and replaced the defective Woodmaster backflow preventer component, which was causing continuous water flow. Placed collection bucket beneath utility area plumbing connections as a precautionary measure during diagnostics and repair, then tested system to confirm proper operation and water shutoff functionality.

Completed prepaid cooling maintenance visit on air handler unit. Performed electrical diagnostics using multimeter, verifying amp draw at 1.3A and checking capacitor operation with all wire connections secure. Measured and recorded indoor air conditions at 54.7°F and 45.05% relative humidity, confirming proper system performance and airflow.

Completed comprehensive plumbing service including water heater flush, expansion tank replacement, and repair of multiple leaking fixtures. Addressed leaking kitchen faucet and drain assembly, replaced faulty washing machine supply hoses, and installed smart water shut-off system with monitoring capabilities for leak detection and automatic water supply control. All fixtures tested and confirmed operational upon completion.

Completed routine AC tune-up on four-year-old cooling system. Performed standard maintenance procedures including electrical measurements using clamp meter, recording amperage draw of 5.08A and voltage readings on outdoor unit. Inspected condenser coil fins and overall system operation, confirming equipment is functioning within normal parameters.

Responded to call for toilet leaking at floor connection during flushing after extended period of non-use. Upon inspection, identified corroded and deteriorated shut-off valve assembly with significant mineral buildup and water damage. Replaced faulty valve hardware and water supply line, ensuring proper seal at floor flange connection. Tested flush mechanism multiple times to verify leak was resolved and all connections remained watertight under operating pressure.

Responded to callback for leaking hose bib handle. Upon inspection, verified active leak at valve stem packing. Replaced worn packing nut and stem washer on exterior hose bib, tested operation of valve handle for proper function, and confirmed no leaks present after repair completion.

Responded to no-service call for toilet flapper malfunction where flapper valve was not seating properly after flush cycle. Inspected toilet tank components and identified flapper failing to close completely due to chain tension issue and worn flapper seal. Adjusted flush valve chain length to proper specification and replaced deteriorated flapper with new unit. Tested flush mechanism multiple times to verify proper operation and complete tank refill cycle. Flapper now seats correctly, stopping water flow as designed.

Completed cooling maintenance club visit on outdoor air conditioning condenser unit. Performed comprehensive system inspection including electrical diagnostics with multimeter, recording voltage and amperage readings to verify proper compressor operation. Removed and cleaned condenser coils, checked refrigerant lines and connections, and ensured all mechanical components were functioning within manufacturer specifications for optimal cooling performance.

Relocated and installed new gas supply line to pool heater equipment. Removed existing aged copper piping showing significant oxidation and replaced with code-compliant gas line from meter to heater unit. Completed pressure test to verify system integrity and absence of leaks throughout entire gas line installation.

Responded to service call for water heater failure with no hot water production. Upon arrival, inspected 20-year-old tanked water heater unit that had reached end of serviceable life expectancy. Evaluated existing plumbing configuration including pressure regulation system with Calfi brass pressure regulator valve set at 0.75 PSI, pressure gauge assembly, and copper supply line connections with braided flexible connectors. Assessed water heater installation including base mounting on gray platform, black vertical supply piping with red-handled brass shutoff valve, and dual port connections at unit base with red and blue indicators. Verified all plumbing connections, compression fittings, and metal clamps securing vertical pipe runs. Documented condition of existing low-lead compliant components and overall system configuration. Given the age of the unit matching the home's 20-year construction date and repeated failure to maintain water temperature, recommended replacement as most co

Completed water heater upgrade from traditional tank-style unit to tankless system. Removed existing cylindrical tank water heater and installed new Lochinvar tankless unit with proper copper piping connections, valve assembly with temperature controls, and integrated expansion tank. Ensured all connections met code requirements and system was tested for proper operation and leak-free performance.

Responded to emergency call for sump pump alarm activation with water backup. Upon arrival, inspected sump pump basin and found pump mechanism submerged and non-operational. Removed debris and sediment from basin interior that had accumulated around pump housing. Tested pump motor function and verified electrical connections were secure. Identified exterior discharge line issue with water pooling at termination point. Excavated discharge area to expose piping and corrected drainage slope to ensure proper water flow away from foundation. Cleared blockage from discharge line and repositioned outlet pipe. Backfilled excavation site and restored grade. Tested complete system operation by running pump through multiple cycles to confirm proper water evacuation and alarm reset. System restored to full functionality with no further backup issues detected.

Responded to emergency no-heat call on furnace system. Upon arrival, performed comprehensive diagnostic testing using Fluke multimeter to assess electrical components and system functionality. Inspected blower motor assembly, internal wiring connections, and control board circuitry. Evaluated motor capacitor, transformer output, and verified proper voltage supply throughout the unit. Checked all wire terminations and electrical connectors for secure connections and signs of failure. Measured temperature differentials and assessed overall system operation to identify root cause of heating failure.

# Tankless Water Heater Installation Successfully installed a Navien tankless water heater unit in the basement utility area. The installation included proper venting, gas line connection, and water supply integration with existing plumbing infrastructure. All electrical connections were completed to manufacturer specifications, and the unit was mounted securely to the foundation wall. System was tested for proper operation, including flow rate verification and temperature settings. The installation area was left clean and organized with all components functioning as designed.

Responded to drainage backup issue occurring during heavy rainfall events. Performed thorough assessment of main drain system and identified standing water and debris accumulation in primary cleanout access point. Conducted camera inspection revealing sediment buildup and drainage restrictions within main line. Executed mechanical snaking of main drain to remove blockages and restore proper flow. Cleared additional exterior drainage points around property that had not been previously serviced. Recommended installation of sump pump system to prevent future water intrusion during storm events, as property currently lacks adequate water management infrastructure for handling large volume rainfall.

Completed scheduled maintenance on reverse osmosis water filtration system, replacing both pre-carbon and post-carbon filters as required. Additionally addressed broken utility tub handle that was discovered during service visit. All plumbing connections inspected and system verified operational upon completion.