Heating, AC & Plumbing in Beachwood, OH

Responded to a leak around the base of a toilet in a 40-year-old residence. Upon inspection, identified the issue stemming from a deteriorated wax ring seal between the toilet and the floor flange. Shut off the water supply at the floor-mounted angle stop valve and disconnected the chrome supply line from the tank fill valve. Removed the toilet by unbolting it from the floor flange, then scraped away the old wax ring residue from both the toilet base and the closet flange. Inspected the flange for damage and confirmed it was secure and in acceptable condition. Installed a new wax ring with plastic horn onto the flange, carefully repositioned the toilet to ensure proper alignment with the mounting bolts, and compressed the seal by applying even pressure. Reinstalled and tightened the closet bolts to manufacturer specifications, being careful not to over-torque and risk cracking the porcelain. Reconnected the water supply line, opened the angle stop valve, and filled the tank. Conducted

Responded to callback for persistent shower head leak after previous service attempts. Performed thorough inspection of shower assembly and fixture connections. Applied leak detection solution to identify source of drip and tightened all valve seats and compression fittings. Verified proper water flow and confirmed complete resolution of leak with no further dripping observed during extended test period.

Return service visit to install new body sprayer head and cartridge assembly that was previously sold and ordered. Upon arrival, verified the replacement parts and completed the installation in approximately two hours. All components tested and confirmed operational.

Completed routine cooling maintenance member visit on air handler system. Performed comprehensive inspection of evaporator coil assembly, verified refrigerant line connections and U-bend piping configuration for proper alignment and secure fittings. Inspected blower motor assembly, confirmed operational status of squirrel cage fan wheel, and verified all electrical connections at motor terminal block. Documented system components including heat exchanger fins and internal cabinet condition. All components found operating within normal parameters with routine dust accumulation noted on interior surfaces, typical for seasonal operation.

Completed cooling maintenance on two HVAC units. Performed electrical diagnostics using multimeter to verify amperage and voltage readings on system components. Inspected and assessed air filtration system, noting filter condition and proper installation in air handler unit. Customer requested provision of replacement filters for ongoing maintenance needs.

Performed seasonal startup service on HVAC system. Verified electrical amperage readings using digital clamp meter on refrigeration lines and measured gas pressure at heating equipment using dual port manometer. All readings within manufacturer specifications. System operational and ready for use.

Completed dual system installation as a follow-up service. Verified proper leveling of all equipment using precision bubble levels to ensure optimal system performance and operation.

Performed rough-in plumbing installation for a temporary kitchen sink in the basement to be used during main kitchen renovation. Installed necessary copper and PVC piping connections to existing plumbing system. Positioned utility cabinet in corner location with appropriate access to water supply and drainage.

Conducted diagnostic inspection of HVAC system using borescope camera to examine interior condition of heat exchanger tubes. Visual inspection revealed signs of corrosion along edge of heat exchanger. Inspected electrical connections and wiring harness (red, blue, white, and yellow wires) to verify proper installation and identify potential issues contributing to furnace malfunction.

Completed follow-up service call to replace the hydro water panel in customer's humidifier system. Removed old humidifier panel which showed significant mineral deposits and discoloration throughout the honeycomb structure. Installed new water panel to restore proper humidification function and ensure optimal system performance.

Responded to customer report of water leak in HVAC room where customer had proactively shut off humidifier. Inspection revealed condensate line issue at the connection point with visible water damage on floor. Sealed joint with appropriate compound and verified proper drainage function to resolve the leak.

Responded to service call for no hot water in the residence. Diagnosed frozen water supply lines affecting the water heater system located in the utility closet. Thawed affected pipes using approved methods, restored water flow, and verified proper operation of the 5-year-old water heater unit. System now functioning correctly with normal hot water supply throughout the home.

Successfully installed a Kobella tanked water heater in basement utility area as a return service. Installation included proper connection of copper inlet/outlet pipes, mounting of expansion tank, and connection of metal ventilation ducting. System includes DEFENDER safety features and all necessary valves, with all components securely mounted to the wall structure.

Completed installation of complete HVAC system as part of return service sold by Justindz. Performed pressure testing with CPS V220 digital manometer to verify system integrity. Installed and connected new furnace with proper electrical connections and PVC condensate drainage system in the mechanical room.

Inspected 35-year-old gas furnace with air conditioning system that customer reports is struggling to maintain temperature. Visual examination revealed multiple holes in the heat exchanger as previously identified by another technician. Documented extensive condensation on metal surfaces and photographed the current system configuration in preparation for full system replacement recommendation.