Dedicated Heating, Cooling & Plumbing Services in Wickliffe

Performed annual heating system maintenance and verified combustion performance using a Testo 310 combustion analyzer, recording O₂ at 8.8% and CO₂ at 6.79% to confirm safe, efficient burner operation. Tested electrical components with a True RMS clamp multimeter to verify proper amperage and voltage readings, and confirmed the system is operating within manufacturer specifications.

Completed the final prepaid maintenance visit on the gas furnace, inspecting the integrated furnace control board and confirming normal operation with the board in idle status and no signs of burn marks, corrosion, or physical damage at the terminals or wiring. Performed combustion analysis with a calibrated flue gas analyzer, recording O₂ at 9.0% and CO at 12 ppm, which is within acceptable limits for safe operation.

Performed a full-system estimate for a commercial car wash to replace an existing oil-fired suspended unit heater with a new gas-fired Reznor unit heater. Inspected the existing unit, its vent stack and galvanized flue routing through the attic, and the surrounding conduit and ceiling structure, noting soot staining and corrosion that will require attention during the changeover. The scope will include removal of the oil-burning equipment, a new gas supply, and a code-compliant venting configuration.

Performed annual maintenance tune-up and completed furnace start-up following recent system installation, with gas supply pressure previously corrected by the utility. Installed the new thermostat, leveling the subbase and connecting the control wiring. Verified static pressure with a dual-port manometer (approximately 1.75 in. w.c. across both ports) and confirmed proper system operation.

Performed seasonal maintenance inspection on the boiler and furnace, including verification of the control module operation, system pressure (approximately 10 psi at the Caleffi gauge), and associated wiring and piping connections. Identified a humming noise at the furnace blower fan and noted leakage at the boiler, with replacement of the air bleeder line recommended to correct the leak.

Responded to a no-cool call with barely cold air at the vents and inspected the system, including the return air filter at the air handler. Evaluated airflow and system performance, documenting filter condition and unit readings, and performed calculations to verify operating values. Recommended further diagnostics and corrective action as needed to restore full cooling capacity.

Completed full HVAC system installation including outdoor condensing unit and electrical disconnect box. Verified proper leveling of equipment and ensured all electrical connections were secure and code-compliant, with conduit properly terminated at disconnect box.

Responded to emergency maintenance call for leaking gas water heater in basement. Upon arrival, found active leak requiring homeowner to shut off main water supply to prevent flooding. Performed diagnostic pressure testing using digital manometer to assess system conditions and identify leak source. Evaluated need for shut off valve installation to isolate water heater from main supply line for future maintenance and emergency situations.

Completed full HVAC system installation including outdoor condensing unit and indoor air handler. Verified proper refrigerant charge using digital manifold gauges and ensured system was level and securely mounted per manufacturer specifications. System tested and operating within normal parameters upon completion.

Completed return ductwork installation in basement area as part of same-day HVAC system installation. Installed rectangular metal supply ductwork with proper support from existing floor joists, ensuring secure mounting and proper airflow pathway. Verified system performance using digital thermometer, confirming temperature differential readings of 51.8°F and 116.1°F at measurement points to validate proper system operation and air distribution.

Performed comprehensive AC tune-up on 40-year-old air conditioning system currently operating without issues. Conducted standard maintenance inspection and servicing procedures, documenting equipment condition through interior component photography showing copper refrigerant lines, mounting hardware, and cabinet structure. System found to be functioning properly with no reported symptoms or accessibility concerns at time of service.

Completed heating maintenance member visit with emphasis on thorough cleaning of the furnace system and surrounding area. Performed comprehensive inspection of the gas furnace unit, including burner assembly, heat exchanger, blower compartment, and all accessible components, ensuring removal of all cobwebs, dust, and debris from previous accumulation. Cleaned condensate drain lines, verified proper venting through PVC piping system, and inspected all mechanical room components for proper operation and cleanliness to prevent callback situations.

Responded to service call for AC system not turning on, unit previously installed in 2023. Performed diagnostic testing using digital manometer to measure system pressures in both the attic/mechanical space and at the air handler location. Measured static pressure readings of -0.299 and 0.509 inches water column to assess airflow and system performance. Verified equipment operation and completed pressure diagnostics to identify root cause of intermittent operation issue.

Responded to emergency call for leaking water heater in basement that required shutting off water supply to entire house to prevent flooding. Upon arrival, inspected Lochinvar gas-fired water heater and associated plumbing connections. Identified source of leak and assessed overall system condition including expansion tank, copper supply lines, and shut-off valve configuration. Replaced failed water heater with new unit, installed proper shut-off valve to allow future isolation of water heater without affecting whole-house water supply, and reconnected all gas and water lines. Verified proper burner operation and flame characteristics, checked all connections for leaks, and confirmed system functionality. Water heater restored to full operation with no active leaks detected.

Conducted comprehensive assessment of existing HVAC system for replacement estimate, including 40-year-old furnace and 38-year-old air conditioning unit that recently ceased operation. Documented current equipment conditions, thermostat wiring configuration, and outdoor condenser unit placement for system replacement planning. Provided detailed replacement options and recommendations for complete heating and cooling system upgrade.

Completed full HVAC system installation including indoor and outdoor units. System was charged with refrigerant to manufacturer specifications using manifold gauges, with pressures verified and documented. All connections were tested and confirmed leak-free, with system operational and ready for service.

Installed and secured valve assembly as part of larger plumbing system integration. Mounted copper refrigerant lines to metal ductwork using appropriate brackets and hardware, ensuring proper positioning and support of pipes throughout the installation area. Applied spray foam insulation to foundation surfaces to complete thermal envelope requirements for the system.

Completed prepaid club maintenance visit on air handler unit. Performed diagnostic testing of electrical components using digital multimeter, recording temperature and amperage readings to verify proper system operation. Inspected evaporator coil assembly, confirming fins were clean and free of debris with proper spacing maintained throughout. All components operating within normal parameters at time of inspection.

Responded to service call for air conditioning unit with non-operational fan. Performed diagnostic assessment of HVAC system located in basement utility area, evaluated mechanical components including furnace unit, ductwork connections, and related infrastructure. Generated estimate for complete system replacement based on equipment condition and operational requirements.

Responded to no-cool complaint on aging residential air conditioning system. Upon inspection, found heavily clogged air filter restricting airflow and preventing proper system operation. Inspected control board and electrical components for additional issues. Replaced dirty filter and verified proper fan motor operation and system functionality. Unit restored to normal cooling operation.