Chardon Plumbing, Heating & Cooling

Successfully installed customer-provided hot water tank along with a new thermal expansion tank and brass shut-off valve for the humidifier. Completed necessary repiping of 2" flue venting for the furnace to accommodate the hot water tank installation, with materials provided by customer.

Performed site assessment for gas line installation in an unfinished interior space with exposed framing and joists. Evaluated existing wall-mounted heating unit connections and documented current infrastructure including HVAC components. Provided quote for complete gas piping service to properly supply the heating system while ensuring code compliance during ongoing construction/renovation.

Diagnosed Amana furnace displaying E2 code and no heat production. Inspection revealed voltage issues at 25.4V as confirmed with SC480 multimeter. Replaced faulty control board and verified proper operation of all electrical components, restoring normal heating function.

Responded to a water leak call at a residential property where water was dripping from a pipe joint in the basement. Upon inspection, discovered a section of copper supply line with visible oxidation and corrosion requiring access through drywall. Extracted a small metal pin that had punctured the pipe, repaired the damaged section, and verified system integrity with pressure testing before departing.

Performed diagnostic on system and identified faulty coil sensor reading low. Inspected control board and wiring connections in electrical panel. Ordered replacement temperature sensor and defrost board to resolve issue. Documented condition with photos of circuit board and electrical components.

Conducted site assessment for multi-zone mini-split system installation. Revised original estimate to exclude office space as requested, focusing on 2-head configuration only. Inspected electrical panel and existing plumbing infrastructure to determine optimal placement for condensate lines and refrigerant piping.

Successfully installed new kitchen faucet with pull-down spray feature. Completed proper connection of supply lines and verified drain assembly was secure and leak-free. Final inspection confirmed full functionality and proper operation of the new fixture.

Responded to warranty call for humidifier move control issue. Accessed and inspected HVAC system in basement utility area, focusing on the connection between furnace unit and ductwork. Successfully restored proper functionality to humidifier control system as per warranty requirements.

Responded to a callback regarding persistent odor and intermittent foaming in kitchen and bathroom water supply. Inspected water softener system, noting proper salt levels and function. Previous chlorination treatment of well had not resolved the issue. Documented water quality issues and recommended comprehensive water testing to identify potential contaminants causing the persistent odor and foam.

Inspected wall-mounted gas heater in garage. Unit is properly installed with required electrical connections and appears to be functioning correctly. Gas line and shut-off valve are in good working condition.

Successfully installed Aprilaire 720 Humidifier on existing HVAC system in utility area. Connected unit to furnace ductwork with proper copper piping configuration, and verified digital control panel functionality. Completed installation and documented with photographs of final setup showing proper integration with the main furnace unit.

Successfully installed CPVC piping to connect the A.O. Smith water heater to an above-ground storage tank as part of a coordinated job with humidifier installation. Properly insulated connections and verified all fittings were secure with no leaks present upon completion.

Performed warranty service call to inspect electrical disconnects mounted on exterior wall. Examined junction boxes showing deteriorated weatherproofing and potentially unsafe wiring connections. Replaced defective disconnects with new units, properly secured all electrical connections, and applied appropriate sealant to ensure weather-tight installation per manufacturer specifications.

Inspected outdoor HVAC unit where gravel was washing out from under the pad down the slope. Installed wooden frame structure around the unit's base to contain gravel and prevent further erosion. Documented installation with photos showing the completed erosion control solution.

Successfully completed installation of a power vent water heater with proper exterior PVC venting. Installed new water heater, connected all necessary plumbing and electrical components, and ensured proper venting through exterior wall. System tested and confirmed operational.

Performed warranty service on HVAC system, replacing defective motor as specified in warranty claim. Inspected ductwork and connections in basement utility space, ensuring proper installation of replacement component and verifying system functionality after repair.

Installed foam insulation for sewage crock lid to provide proper sealing. Ran new gas line for customer's stove and installed water supply lines for two sinks, ensuring all connections were properly secured and tested for leaks.

Cleared severe kitchen sink clog by accessing drainage system in basement where previous service attempt had failed. Inspected aged copper piping with visible corrosion at T-junction, then successfully used high-pressure equipment to remove blockage and restore proper drainage function.

Removed and replaced two toilets - installed one standard model and one ADA height unit. Replaced corroded flange on first toilet and installed new wax ring to ensure proper seal. Both units successfully tested for proper function and leak-free operation.

Performed warranty service on heat pump system. Diagnosed evaporator coil with significant frost buildup and ice formation on refrigerant lines. Corrected refrigerant charge and cleaned coil surfaces to restore proper heat exchange functionality and system operation.